Also UK gallons are a bit bigger...
Also UK gallons are a bit bigger...
A Land Rover would never turn up to collect an Oscar. It'd be far too busy doing something important, somewhere, for someone."
hence the 20 mp(US)g in my response. The fuel consumption of these things seem to be an ongoing debate. I have a bog standard RRC (not the S$$T!) that I've been playing with to see what can be acheived. Cannot get 25mpg avg. Can get 23 all day long, short trip, long trip, full of people , empty, towing a small boat.....doesn't matter. Does go down a bit if you drive over 65mph. Considering the same rig with the V8 did about 12-13 mpg it's a pretty good gain but will still take allot of driving to pay for itself. it had a brand new crate motor (factory kit) installed which for an RRC with AC and the correct trans, cruise control etc. runs about 26K (installed).
I get people dropping jaw on a daily basis ( yours too I think eh daveb?) it seems with the cost of these diesel installs. I also have more of them to do than I can schedule right now. There must be some sort of value in it, and I'm certainly not getting rich quickly (sort of a slow smelly rich!).
interesting, good point making the distinction, I had forgot the difference between UK and American gallons
26K for an engine install . . . kind of speaks for itself
unless you're in NYC or SF or something
some US owners on a US overland site reported this week the following;
low to mid 20s on a Defender 130 @ 65mph, 300tdi
200tdi 28-30mpg D110
TD5 26-28 @ 65mph D110
another TD5 owner 20-24 even @ 85mph D110
so I guess it varies
looking at the increase in availability in 25yo imports with diesels, it appears is most likely the way to go or just have a conversion done in the UK before shipping, even with currency exchange it would be far cheaper, which says a lot
I'm at a loss to understand how the cost would run north of $12-15K. $26K? what's your labor rate? do I get a diamond ring with that? or some fries?
then again, in America you can really spend as much as you want on anything you want
just teasing, sounds like you do superb work especially if you're booked up
there is a 200tdi coming in this week and 7 more diesels otw from another place I am exploring, let you know how it goes
thx again everyone for your insight and wisdom
Indeed, although I wasn't really surprised, just confirmed what I already knew. Was hoping mine could somehow be done on the cheap, for some reason. Actually probably would have been more than quoted due to all the non standard crap that I did
Zoo, you don't even want to know the cost of a new complete 300tdi engine. I'm afraid I will always be stuck with the junkyard units from the UK...its ok, I've never had a new engine in anything, only rebuilds or "unknown" and I've done ok. Always somewhat of a crap shoot though when buying from overseas.
A Land Rover would never turn up to collect an Oscar. It'd be far too busy doing something important, somewhere, for someone."
Dave love your signature quote from RH, that is a superb video isn't it?
would your recommendation then to either have it done in the UK overseen by a friend or just get a whole package and take my luck with an import?
what issues should I look for in a 200 or 300 that is used or what expectation should I have on a refurbished one?
many thanks!
I will personally vouch for Matt's quality of conversions. He is not a mechanic he is a craftsman. I had him do a straight NAD conversion on my 88 late last summer. Everyone who looks at the end result tells me that unless you know it was a gas job in it's prior life you wouldn't know the difference. Matt will tell you and so will the folks at ECR that you don't do a diesel conversion to save one red cent. You do it because that is what you want. Will the conversion save me any money, NO! Would I do it again, YES in a heartbeat! I am super pleased with my oil burner and wouldn't have my Rover any other way but I simply love diesel engines. The added benefit to my diesel fume induced happiness is that I have gained a great true friend in the process. In short, make sure you do any conversion be it diesel or souped up gas engine for the "right" reasons by the right shop or you will, in my opinion, end up with a piece of junk and tons of headaches.
Jim
I'm sure that is true and no one is questioning the skills of Rover mechanics, just the prices and the potential of doing it yourself. To avoid the whole economic supply/demand niche market thing, yes people pay it, happily
does that mean you can't have a good reliable engine installed, that will perform well, put in by a novice or assisted; of course not. It isn't one way or the other. We are talking car mechanics/engines, not mapping the human gnome. Yes it requires attentiveness but it should not require 10-20K large UNLESS you want everything absolutely done new to perfect specs.
exploring it some more:
It seems the best way to go is buying an import with a diesel already installed unless you want to go to the UK and travel a bit, what a great opportunity. A sleeping bag, passport, and a map would be a fun time if you can buy a good reliable runner. Then ship it over. This will cost less from buying an import but you're gambling until you get the rig inspected and you know what to look for. I don't . . . yet
But if you want to say finance the deal, the car must be in the country already so that limits your options but not in a bad way. There are some nice rigs coming into the country for less than 20K$US
I guess as the conversation evolves, the real question is; what do I look out for when inspecting a refurbished or used diesel engine? 200/300? obviously rust, condition, type/amount of smoke out the pipe, sound, gear suppleness, etc.
what are the typical downfalls of each engine? we have access to some great experts here so this should be straight forward? If I was going to look at a US V8, I'd look for records, oil, leaks, valve issues, belts, last major service, fluids, etc. Most likely that won't be an option, but there have been half a dozen or so one owner imports coming in at good prices that do have service records
can anyone knock out a list of considerations when looking at a used rover diesel?
Not sure what you mean by conversions speaking for itself or the NYC/SF connection but the 26k install is for 18+K in new factory parts and and 100+hrs at shop rate of 75/hr. That's for a spanking new factory motor / trans and all AC / cruise control / every part that would have been on this car if factory built. If you were to drive it or look under the bonnet it would certainly speak for itself. It's a car you cannot buy here, cannot import here and is rare even in Europe.
I'd suppose you'd get a real laugh at the 100k+ plus Defenders that roll out of my shop.
I deal with 200tdi all the time also and they don't get better mileage than a 300.
I also deal with TD5's which do get very slightly better mileage....still not the range I see quoted frequently.
Anyhow....good luck with it. I'm not trying to be a buzz kill. It would in theory be to my advantage to inflate the actual performance figures of these things, and to deflate the cost. Just keeping it real.
thanks Matt, appreciate your wisdom and experience
can you tell me what to look out for when gauging a 200/300 as far as major issues besides leaks or basic commonsense stuff?
again, thanks!
love to see some of your work if you want to post up some pics
For the most part leaks are about all you have to look for. I like to replace the timing belt and tensioners, front and rear main seals and fuel lift pump regardless of history. I generally do all the hoses. Service history or an acurate mileage count is nice.
Photos of an International 2.8 TGV (stroked 300tdi in drag) currently being installed. Not completed.....need a couple more days on that.