Activity Stream

Sort By	Time	Show
Recent Recent Popular Popular	Anytime Anytime Last 7 Days Last 7 Days Last 30 Days Last 30 Days	All All Photos Photos Forum Forums

Today, 01:33 PM

firefighterjed replied to a thread 1965 Series 2a in Idaho, A build thread. Many questions in Land Rover Series I, II, IIA & III

list of parts acquired so far: 302 to replace seized motor. -cheap from a friend. Rebuild kit -Rock Auto Motor mounts -Speedway Motors Radiator...

3 replies | 28 view(s)

Today, 01:24 PM

firefighterjed replied to a thread 1965 Series 2a in Idaho, A build thread. Many questions in Land Rover Series I, II, IIA & III

Loading her up Bringing her home. Garage full of landy (note the home made radiator panel and grille)

3 replies | 28 view(s)

Today, 01:16 PM

firefighterjed replied to a thread 1965 Series 2a in Idaho, A build thread. Many questions in Land Rover Series I, II, IIA & III

pic from the FOR SALE ad

3 replies | 28 view(s)

Today, 01:14 PM

firefighterjed started a thread 1965 Series 2a in Idaho, A build thread. Many questions in Land Rover Series I, II, IIA & III

I figure it would be good to document the adventure of getting my Rover up and running. A group of my friends who all have 4x4s posted a link to...

3 replies | 28 view(s)

Yesterday, 08:56 PM

Elsa replied to a thread Reverse lights inoperable due to reverse shift rod rotating? in Land Rover Series I, II, IIA & III

@MJL, Your 2017 referenced post is the same set up as my above photos. The only difference seems to be my photos are of a late 2A vs. your Series 3.

6 replies | 349 view(s)

Yesterday, 01:05 PM

jvsimmons started a thread diesel injection pumps in Land Rover Series I, II, IIA & III

I have two diesel injection pumps that I need to get rid of,. One is from a 1983 Series 3 with cable linkage - the pump leaks from the base of the...

0 replies | 31 view(s)

Yesterday, 12:51 PM

jvsimmons replied to a thread Series 3 diesel sedimenter drain plug in Series I, II, IIA, III

Thank you roverp480. Interesting. I cannot find the sedimenter.....I'll crawl under and have another look. Service book says it's attached to the...

2 replies | 99 view(s)

08-04-2022, 02:36 AM

roverp480 replied to a thread Series 3 diesel sedimenter drain plug in Series I, II, IIA, III

Its a normal right hand thread so counter clockwise to unscrew. If its the standard CAV sedimenter its possible its a plastic plug which can easily...

2 replies | 99 view(s)

08-03-2022, 04:54 PM

Poppy1969 replied to a thread Rocker Pedestal Question in Land Rover Series I, II, IIA & III

UPDATE! Crisis averted : ). I should have just taken a peek. The center pedestal does not cover the freeze plug completely. I can see it being...

2 replies | 114 view(s)

08-02-2022, 09:43 PM

jimrr replied to a thread III stalls and revs then dies in Land Rover Series I, II, IIA & III

again, unaccounted for rpm changes can usually be attributed to carb issues. As previously mentioned timing advance/retard can do this quite...

11 replies | 330 view(s)

08-02-2022, 09:38 PM

jimrr replied to a thread Rocker Pedestal Question in Land Rover Series I, II, IIA & III

OMG , !! UNtorquing the head is a no no, wait till someone with some brains sees this post .......... just take a steady strain and hold !!

2 replies | 114 view(s)

08-02-2022, 05:56 PM

Poppy1969 started a thread Rocker Pedestal Question in Land Rover Series I, II, IIA & III

Hello. For the longest time I wondered where the small freeze plug might go that came in my cylinder head gasket set. The other day I noticed on a...

2 replies | 114 view(s)

Welcome to the Rovers North Land Rover Forums. Register A New Account.

Browse Rovers North's Parts Catalog:

About us

Links

Join us