View Full Version : Oil temp/Water pressure fitting
utahseries
02-15-2011, 10:47 PM
I'm wondering if anyone knows the sizes for the male/male adapter that screws into the block, then you screw the water temperature sensor into that? It's part # 568457. I was just wondering if anyone knew the thread sizes to see if I could source something locally.
TeriAnn
02-16-2011, 06:12 AM
I'm wondering if anyone knows the sizes for the male/male adapter that screws into the block, then you screw the water temperature sensor into that? It's part # 568457. I was just wondering if anyone knew the thread sizes to see if I could source something locally.
The male to male adapter that fits a female fitting at the sensor bulb of a Smiths mechanical temp gauge on one end and and screws into a threaded engine hole at the other end.
I could use one of those as well. Anyone know a source for these male to male adapters??
kevkon
02-16-2011, 07:12 AM
You might try EGauges.com. I got all of my adapters from them.
Terrys
02-16-2011, 07:12 AM
I'm pretty sure of two things: It looks like this, but this isn't it. I think I have a few, and if it get's above 10 degrees, might be able to go upstairs in the barn for a look for the right ones. I'll need to find a butterfly gage to check it against too.
I have a 10' piece of hex brass and can set up the Gallicop to make a bunch, but it'll have to wait till sugaring is over.
Terrys
02-16-2011, 07:15 AM
Might help if I showed wth I'm looking at.
kevkon
02-16-2011, 07:16 AM
One thing that's a PIA is that some threads are BSP which can easily be confused with NSP. I think its 27 tpi vs 26tpi.
luckyjoe
02-16-2011, 08:16 AM
I have the dual gauge kit installation instructions and part number list at home. I can post it tonight...
jac04
02-16-2011, 08:39 AM
568457 is a male / female adapter used to install the electric water temp sending unit (560794) into the head. It is used with sealing washer 243959.
568457 should be readily available for $10. I bought one not too long ago (from Bill at tntlr.com): http://www.tntlr.com/content/adapter-wtemp-imp
Terrys
02-16-2011, 09:03 AM
The newer Smiths butterfly gauges have a male barrel that holds the bulb into a M/F adapter too. I know I have those, not sure about the M/M ones till I get out to the barn (mine, not the flat one)
TeriAnn
02-16-2011, 09:12 AM
Might help if I showed wth I'm looking at.
Interesting.
I am looking to put the gauge sending unit adapter on one of these:
http://www.tjwakeman.net/Images/TWTR.jpg
Terrys
02-16-2011, 10:34 AM
TA, I knew that pic would get your attention.
utahseries
02-16-2011, 11:02 AM
Terry, that is exactly what I'm looking for. Lemme know if you find any in your search.
jac04
02-16-2011, 12:01 PM
I'm wondering if anyone knows the sizes for the male/male adapter that screws into the block, then you screw the water temperature sensor into that? It's part # 568457.
For reference, the correct part numbers are:
218512 Union for thermometer bulb, Petrol models
243959 Joint washer, union to cylinder head, Petrol models
rover_chump
02-16-2011, 02:14 PM
Greetings Utah & Terri...... Just spoke with Les here and he happens to have two of those adaptors left in his stash... Give him a call.
Les Parker
02-16-2011, 02:53 PM
I had some of these machined a few years back.
I have 2 of them left @ $20.00 each.
Let me know.
Terrys
02-16-2011, 03:52 PM
Terry, that is exactly what I'm looking for. Lemme know if you find any in your search.
Well,it is and it isn't. It's for a BMC engine, or maybe it was a 120, but it's not the right size for a LR. Best get one from Les. I did find some today, but they are M/F, for the later style with the male threaded barrel.
TerriAnn, I have probably had 25 English sports cars, and not one Triumph ever. Not for not wanting to, just never happened. Nothing beyond TR4 ever did much for me.
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.