Self-bleeding tool.....what do you all think?

[knac1234]

So I am looking to flush out the fluid on my MGs, but also want to look at the clutch pedal on my Rover since I have not been happy with it since replacing the master/slave/hose (still think there is air in the system as it seems too spongy).

Add to that, I am trying to find a tool to do it on my own (so I can remain in good graces with the wife!!!).

Anyone used this:

http://www.speedwaymotors.com/Phoenix-Systems-Reverse-Bleeder,48050.html

http://www.youtube.com/watch?v=FB8kzUEqK3U

It seems to be logical, to force air up, in its natural direction. And it allows me to do it alone. Most comments I've found on line are positive. I suppose I should flush new fluid through the system prior to doing this also (at least on the MGs, as the Rover fluid is new).

Comments? If it truly works I am happy to pay the $65 for a tool to use on all the classics.

Thanks,

Julian

[giftshopduane]

I like it.. seems to be a good way to go. We use this with good success here in our shop.
http://www.harborfreight.com/brake-fluid-bleeder-92924.html
I also have this which I like too..
http://motiveproducts.3dcartstores.com/Black-Label-European-Bleeder-0109_p_101.html

But I'll be honest that looks like a neat tool, might look into one myself. I have a small check valve bleeder, it was like $4 at the local shop..just put it on the bleeder and pump it has a check ball that works well.

[knac1234]

Thanks for the quick reply!

I looked at the systems you show also. The only hesitation is that the brake master reservoir cap on my BGT is very large (I think 3-4" in diameter), and I am concerned that the caps provided in those systems will only fit my other cars.....trying to find something for all :)

Julian

[cedryck]

There are universal style caps that have an oversized top on them, with an elastic or chain style strap that holds it to the top of larger master cylinder containers. One of the replacements brake fluid holders sold by our hosts is plastic and has a large mouth about three inches, master brake bleeders sold by Motive, or Speedibleed do not fit something this large it is much larger that the smaller stock Land Rover master. Having something that fits properly and leak free is imperative in getting this operation to function well.

[knac1234]

Well took the plunge after talking to a few people, and ordered the Phoenix reverse DIY bleeder. Once I get it and try it out, I will post my results on here!

Julian

[rrc.swb]

Julian,

I purchased the one sold by Advance Auto and I bleed my clutch on my own without a problem.

http://shop.advanceautoparts.com/webapp/wcs/stores/servlet/product_Vacuum-Pump-Brake-Bleeder-Kit-Sunpro_9020007-P_N3378_T|GRP2007___

[I Leak Oil]

All these fancy tools...Pump, hold, shove 2x4 between pedal and seat box, get out, open bleeder, close bleeder, repeat. Cheap as dirt and works everytime!
My mighty-vac works well also.

[Terrys]

All these fancy tools...Pump, hold, shove 2x4 between pedal and seat box, get out, open bleeder, close bleeder, repeat. Cheap as dirt and works everytime!
My mighty-vac works well also.

You said it all ! I use my mighty Vac for lots other than bleeding too. The 2x4 is also a good way to chase brake light issues (yes, they happen)

[printjunky]

I built something like this: http://faculty.ccp.edu/faculty/dreed/campingart/jettatech/bleeder/index.htm

I have a Ford dual system M/C, so I found an extra cap at a pull-a-part and made dual fittings to the bleeder. Seems to work pretty well.

[knac1234]

Well I got the tool today. Will try it out on the clutch hydraulics this weekend and see what happens!

Julian