I am still looking

[Paul and Judson]

Part #395246 x 2. Stud bracket for the pick-up top used to attach seat belt anchor brackets.

I have checked everywhere in the US, UK and Australia. But maybe I missed a place or two??

Anybody have the part or an idea where I can look? Thanks.

Paul

[lumpydog]

Try posting a "wanted" ad over at GNR (http://www.gunsandrovers.com/forumdisplay.php?f=6). I've never seen a wanted post there go unanswered.

[Paul and Judson]

I did post it on GNR but it was under the " most un-obtainable thread" not as a stand alone thread. I did get suggestions but I had tried them all before I posted. Thanks. I will try a stand alone post.

[superstator]

You try these?

http://www.roversnorth.com/ProductDesc.aspx?code=PLF469
http://www.roversnorth.com/ProductDesc.aspx?code=PLE267

Sounds like genuine is completely NLA

[Paul and Judson]

Thank you. I have these parts. It is the part that allows you to attach these parts to the truck cab that I need. If you go to RN series parts exterior, then to the seat belt tab, then to truck cab, and look at part # 18, that's the part I need. Notice # 18 is not even listed in the parts description below the picture.

[Les Parker]

These parts do not look difficult to make, I'm sure a local fab shop could make those for you.
The alternate is to fit these :-

http://www.roversnorth.com/ProductDesc.aspx?code=PLB964&type=0&eq=&key=it

[SafeAirOne]

Thank you. I have these parts. It is the part that allows you to attach these parts to the truck cab that I need. If you go to RN series parts exterior, then to the seat belt tab, then to truck cab, and look at part # 18, that's the part I need. Notice # 18 is not even listed in the parts description below the picture.

Perhaps there is a link that we can click on that will take us to the deeply-embedded page that you describe?

[Paul and Judson]

Thank you I will try to do as you suggested. In the mean time it is in the RN parts section Series Parts -INTERIOR ( not Exterior as previously mentioned) SEAT BELTS, TRUCK CAB. PART #18 in picture.

[slowmo]

http://www.roversnorth.com/Land-Rover-Parts/85

Correct link?

[Paul and Judson]

Thank you. This is the correct link. Under truck cab 88 and 109. Part #18. This is what I am still looking for. I need two. Anyone out there with them? Or any suggestions.

[superstator]

A few UK sites don't explicitly say they can't get it, like Craddock or LRDirect, but it others call it permanently unavailable, and they all list ludicrous prices. It sounds like most people just make their own. From the look of it you'd just need a few inches of angle iron, a hacksaw, and a good drill bit.

[Paul and Judson]

Thank you. I checked with Craddock, LR Direct, etc. they cannot get it. Maybe making it is the answer.

[lumpydog]

Have you emailed Ike (pangolin4x4) to see if he has one?

[MJL]

What are the dimensions of the bracket ? It's difficult to get a clear idea of what the brackets look like. I've got 2 brackets that look like they may be similar1100511006

They are close to 2 3/4 inches width. Distance between mid points of threaded studs and captive nuts is 1 7/8 inches.

I "think" I got them years ago when I bought inertia seatbelts for my Ser III station wagon but I can't be sure.

If you think these might be the ones then let me know.

Mike

[Paul and Judson]

Thank you for taking the time to send pictures. These may be what I need. I am out of the country now. I will check sizes tomorrow when I get home tomorrow. If these are the brackets and you want to sell, I am your buyer. Where are you in NH. I am in Maine.

[MJL]

I'm down in the Southern part of the state in Amherst. Let me know if the measurements work.
They've been sitting in my basement for over 10 years so wont be going anywhere until I hear from you :D

[Paul and Judson]

I measured this AM. These are the parts I need. I will buy them. Let me know what you want for them. I will send you a PM so we can make arrangements.

[Paul and Judson]

Thank you for your generous offer. PM sent to you with my street mailing address. In case you need it my email is pstar10@roadrunner.com
Paul

[MJL]

Got it. Will put them in the mail on Monday

Mike

[Paul and Judson]

Thank you.

Paul

[Paul and Judson]

I am not looking any more thanks to the kindness of MJL. Go them today. Thanks Mike.

Paul

[Les Parker]

Great news.
Glad to know all panned out and thanks for the support of the community